Hi Dave
Couldn't you use the back wall of the shed, 100mm pipe or two, to the pond, then build a frame and cover with whatever.
My pond plains are all in place, just got to raise the 15 grand that it will cost.
My good lady has agreed to me nicking 15ft of the back of the garden, so it will be 15 X 15 ( the rear wall being somewhat circular so we won't know the true gallonage till it’s finished ), by 9ft deep which will probably be 8.5 ft by the time the slabs in.
So hopefully 8 / 9000 galls
Regards
Andy
Disguising a Bakki Shower
Moderators: B.Scott, vippymini, Gazza, Manky Sanke
Hi Andy
Thought about mounting externally to the shed etc but lose the benfits of that nice cozy enviroment, did some exploration work and have undone the roof from the walls, (I hope) just need to jack up a foot, add a bit in with some cladding, roof lift done.
You must have been very nice to the Wife to pinch some more garden!! Good news ..
Mike sent me a couple of pics of a remote bakki set up, this one of the fish is pretty inspirational
Regards
Dave
[img]http://i197.photobucket.com/albums/aa98/dav ... G_4449.jpg[/img]
Thought about mounting externally to the shed etc but lose the benfits of that nice cozy enviroment, did some exploration work and have undone the roof from the walls, (I hope) just need to jack up a foot, add a bit in with some cladding, roof lift done.
You must have been very nice to the Wife to pinch some more garden!! Good news ..
Mike sent me a couple of pics of a remote bakki set up, this one of the fish is pretty inspirational
Regards
Dave
[img]http://i197.photobucket.com/albums/aa98/dav ... G_4449.jpg[/img]
Hi Dave
Hi Gaz
Yeah, Mike's main pond, is a cracker .............. some of the fish ain't to bad either
Funny enough, I spoke to Mike earlier today, regarding when we can expect his Tosai in .................. 2nd / 3rd week in May, so I will be getting me arse down there pretty sooooooon
Let me know if you need a hand, when you come to fit it, will gladly pop down ( be nice to see your water ).
Did I tell you I am getting one of those sexy protean skimmers , the next size down from yours.
Regards
Andy
Hi Gaz
Yeah, Mike's main pond, is a cracker .............. some of the fish ain't to bad either
Funny enough, I spoke to Mike earlier today, regarding when we can expect his Tosai in .................. 2nd / 3rd week in May, so I will be getting me arse down there pretty sooooooon
Let me know if you need a hand, when you come to fit it, will gladly pop down ( be nice to see your water ).
Did I tell you I am getting one of those sexy protean skimmers , the next size down from yours.
Regards
Andy
Hi Andy
The pic is enough to keep me going when it comes to the graft of drilling the hole for the return!
Still wondering whether to push one of the returns from the Nexus over the shower as well as the flow from the skimmers? 15000L +16000L+12000 so as 2 meters say 30000L total ie 6600gph or simply run the skimmers which would turn over at around 4400gph.
See the water, hope not!!!
Regards
Dave
The pic is enough to keep me going when it comes to the graft of drilling the hole for the return!
Still wondering whether to push one of the returns from the Nexus over the shower as well as the flow from the skimmers? 15000L +16000L+12000 so as 2 meters say 30000L total ie 6600gph or simply run the skimmers which would turn over at around 4400gph.
See the water, hope not!!!
Regards
Dave
Re: Disguising a Bakki Shower
Hopefully the Bakki pipework is going in tomorrow
Raised the roof on the pond shed by 18" to give me the headroom for a 4 tier shower.
Have drilled the pond wall for the 4” return which will come out at 3’ depth, will be dropping the water in the pond first thing then cutting through the fibreglass from pondside, hopefully squeezing in a 4” tank connector and loads of gold seal.
Shower will be fed from skimmer via Aquamax 16000 and return from a Nexus via Aquamax 15000, pipework from pumps to spraybars is 2”.
4 tier Bakki is 12” above pond level, I am assured the single 4” return will cope!
Plan is to have a 3” spray bar for each input. I was thinking of starting with three rows of holes of 8mm, 60mm apart.
Will put a hole at the top of each spray bar to see if there is excess pressure, if there is then will increase the hole size.
Does this sound like the way to go?
Any views on the optimum amount of BHM I should throw in?
Regards
Dave
Raised the roof on the pond shed by 18" to give me the headroom for a 4 tier shower.
Have drilled the pond wall for the 4” return which will come out at 3’ depth, will be dropping the water in the pond first thing then cutting through the fibreglass from pondside, hopefully squeezing in a 4” tank connector and loads of gold seal.
Shower will be fed from skimmer via Aquamax 16000 and return from a Nexus via Aquamax 15000, pipework from pumps to spraybars is 2”.
4 tier Bakki is 12” above pond level, I am assured the single 4” return will cope!
Plan is to have a 3” spray bar for each input. I was thinking of starting with three rows of holes of 8mm, 60mm apart.
Will put a hole at the top of each spray bar to see if there is excess pressure, if there is then will increase the hole size.
Does this sound like the way to go?
Any views on the optimum amount of BHM I should throw in?
Regards
Dave