Simply Koi and More Koi

will look in to the ties you might have a good point there not sure about tape as the stuff might come lose float in to pump and jam it i might cut a small dia pipe up slide it overair line and solvent weld that to the main feed ? what you think

here is mark two i have taken advice and altered the swept bend a bit from 90 degrees to 45 degrees and i must admit it looks beter and i can see what you ment ,it was one of those jobs i put on paper looked good got the bits and here we are on mark 2 lol i will leave till next weekend so any glue i...

here is my first bit of plumbing thats going in to pond ,i have done filters ect but nothing like this what i would like to know is have i got it right :?: ,i have made sure all the cable clips are trimed and no sharp bits at all anywere, i dont want to undo any bits as i have been playing in the sh...

hi i am in the start of changing to a RETRO FIT AIRATED BOTTOM DRAIN and the pump i want to use has 3 feet of lead i would like it longer and super watertight as the lead needs to go under water has any one here done this ps i am after the top part of the RETRO FIT AIRATED BOTTOM DRAIN as well as th...

would it be worth fitting a 90 degree bend on bottom and running a lenght of pipe to say middle blanked at end and slots at bottom to collect muck from more surface area ,

hello mate i have a spare bit its about 13 inches buy 28 inches 4 mm thick bends nice and wene heated up takes shape you want with a light bend its blue and was a new wheely bin i cut up its what i used in my cloverleaf to keep in the k1 works really well i have two bits that size i am in ipswich an...

i used local search on ebay i done a 10 mile radius from my post code on building materials and pond bits i saved a good bit just on that all adds up

my cl2 is about 12 inches from the base above my pond as its in the shed i would make sure its above ground so you can clean it dont matter how high so long as your pump has enough head to pump it i listed my cl2 in my shed on here so you can see from that its ok look at the post i done it might hel...

i sent a pm but in cash it dont get to you all you need to do to stop them is to split the valve turn the seals 180 derees just put the bottom of the seal to the top this will put the bad fold in the seal to the top and will stop the leak i know ive done both mine as they nip wene you push it back

yes i i would do as last post get a new one there only about £10 delivered on good old fleebay and while you get the new one on order i would get some stainless 5mm cap head bolts and washers and nuts ive done both mine and they undo so much better in the chance of change over seals and the bolts wi...

i have read a few subjects on here about brick built filters a lot say that its hard to work out what you really need and its very hard to change once you have built it i am sure a lot here will tell you the best solution to your needs and the other thing with not building but buying a nexus or the ...

its only about 12 inches long as soon as its to big then i know a very quite lake thats not fished as my mate owns it so it will have a good home wene its about 2 feet long then i will get a small one again ,they dont move fast but the fish moves all over moving the much near the pump Interesting st...

stick with the cl2 filter to keep cost down i have modifyed my cl2 with k1 air and i think it will do double what its ment for even though i have 1500 gallons it will do 3000 with all the mods i can forward photos and small vid clip if you need it also i made my own mannifold with two 8mm tails with...

i have a good size albino cat fish that does no more than the koi but i think my sturgeon moves the bottom surface about more as it hugs the bottom and it has a irregular body movment i have noticed the bottom muck moves a little more were it is and this gives the pump a chance to get it to filter b...

ive been gien a large roll of small bubble wrap about 3 feet wide how can i join this and then a second layer over the top going the other way so nice and strong i dont want to use tape or glue god knows what will happen to the wtaer if it is the wrong stuff what are you all using to joinn it as i c...